|
|
|
Application Profile – |
|
Your parts are produced from: |
What you are looking for: |
__ |
Hand feed stock |
__ |
Coil feed stock |
__ |
Sheet/Strip feed stock |
__ |
Minimum hits with standard tools |
|
__ |
Single hit possibilities |
Type of equipment currently in use: |
__ |
Minimum hits with sub dies |
|
__ |
Low tooling cost – add labor |
__ |
Hard Dies in |
__ |
C-Frame in |
__ |
Turret/Laser |
__ |
Custom hard die quote only |
|
|
|
Press(es) you currently use: |
Run Part to: |
__ |
Hydraulic Press |
__ |
Mechanical Press |
__ |
Pneumatic Press |
__ |
Pierce single subject complete |
|
__ |
Pierce only |
__ |
Hydraulic Brake |
__ |
Mechanical Brake |
__ |
Pneumatic Brake |
__ |
Notch only |
|
__ |
Cutoff |
Comparison Against: |
|
__ |
Turret, Laser |
__ |
C Frames |
__ |
Hard Die |
|
Budget Amount: ____________________ |
__ |
Steel Rule |
__ |
Outside Purchase |
|
|
|
Parts/run: ___________ |
|
|
Parts/year: __________ |
Quotation Requirements: |
|
__ |
Urgent Detail Needed |
__ |
Quick Estimates ± 10% OK |
__ |
Drawings sent via E-mail |
|
|
__ |
Detailed Quote Needed |
__ |
Rush Project |
__ |
Drawings attached _____ page(s) |
|
|
|
|
|
|
|
|
|
|
|
Press Data – Complete section that best describes your most likely press / brake for this project |
 |
 |
 |
Manufacturer’s Name: |
__________________ |
|
Serial Number: |
__________________ |
|
Tonnage: |
__________________ |
|
Stroke of Ram: |
__________________ |
|
Adj. of Ram: |
__________________ |
|
Size of Hole in Bolster: |
__________________ |
A |
________________ |
B |
________________ |
C |
________________ |
D |
________________ |
E |
________________ |
F |
________________ |
G |
________________ |
H |
________________ |
I |
________________ |
J |
________________ |
K |
________________ |
L |
________________ |
|
|
|
|
|
 |
 |
 |
Manufacturer’s Name: |
__________________ |
Serial Number: |
__________________ |
Tonnage: |
__________________ |
Stroke of Ram: |
__________________ |
Adj. of Ram: |
__________________ |
Size of Hole in Bolster: |
__________________ |
A |
________________ |
B |
________________ |
C |
________________ |
D |
________________ |
E |
________________ |
F |
________________ |
G |
________________ |
H |
________________ |
I |
________________ |
J |
________________ |
K |
________________ |
L |
________________ |
M |
________________ |
N |
________________ |
O |
________________ |
|
|
|
|
|
|
|
|
|
 |
 |
 |
Manufacturer’s Name: |
__________________ |
Serial Number: |
__________________ |
Tonnage: |
__________________ |
Stroke of Ram: |
__________________ |
Adj. of Ram: |
__________________ |
Size of Hole in Bolster: |
__________________ |
|
A |
________________ |
B |
________________ |
C |
________________ |
D |
________________ |
E |
________________ |
F |
________________ |
G |
________________ |
H |
________________ |
I |
________________ |
J |
________________ |
|
|